This site uses cookies. By continuing, your consent is assumed. Learn more

130.4m shares

Tall case clock dating advice

opinion

Stand the clock case with the hood removed in the position that you would like your clock to be in. If there is a skirting board at floor level, it may be necessary to Tall case clock dating advice a piece of wood of a similar thickness to the skirting board to the back of the case so that the case will stand up straight and not lean backwards.

If the clock is to stand on a fitted carpet, sometimes the carpet thickness against the wall is greater due to a hem or grip rods. It may be necessary to compensate for this by using a piece of matching carpet or wood and placing it under the front feet so that the case stands Tall case clock dating advice and solid against the wall.

If you wish Tall case clock dating advice screw the case to the wall highly recommended for several reasons this can now be done.

Do check that the case is standing completely upright and not leaning backwards before doing this, as this could cause the pendulum to rub on the back of the case, subsequently stopping the clock. Check also that the visual uprightness of the clock is correct from Tall case clock dating advice parts of the room. There is nothing more annoying than a clock which appears to lean to the right or left when you look at it. Tall case clock dating advice order to get full enjoyment and reliable running from your clock it is well worth paying close attention to this step right at the outset.

The majority of longcase clocks already have one or more holes in the back of the case. It will do no harm. Now, with the clock in the correct position against the wall, put a pencil through this hole and make a mark on the wall. Move away the clock case and drill and rawlplug the hole ready to accept a screw. Tall case clock dating advice a hole in the piece of wood that is to go between the Tall case clock dating advice case. This hole Tall case clock dating advice be slightly bigger than the screw you will use.

Now move the clock case back into position. Feed the Tall case clock dating advice Tall case clock dating advice the hole in the back of the case and also the piece of wood you are using and then line up the screw with the hole you have prepared in the wall. Ensuring that you use a long enough screw to go through everything and also get a good grip, you may then tighten the screw until the clock is held firmly and securely against Tall case clock dating advice wall.

Although longcase clocks can be free standing and often are a multitude of problems can be avoided by following the Tall case clock dating advice above, and securing the clock case to the wall.

Before doing this, always check that the gut or sometimes wire lines are still on the winding barrels and have not unravelled and wound themselves around the winding arbor.

If they have, undo them and put them back onto the Tall case clock dating advice. It may be necessary to undo the guts from the seat board and take the pulley wheels off, to unwind the gut off the spindles. If this is the case, always remember to replace the pulley wheels before fastening the gut back onto the seatboard. Place the movement into the case and position centrally.

Most movements will sit reasonably squarely in the case. As a general rule the movement should be just forward enough Tall case clock dating advice the back of the case, to allow the crutch, through which the pendulum swings, to be free from the backboard. Most pendulums have a front face and back face. The smooth polished part of the pendulum bob, should be at the front.

Feed the pendulum through the door in the clock trunk up through the hole in the back of the seatboard, threading the feather or suspension spring through the eye of Tall case clock dating advice pendulum crutch and hanging it between the cheeks of the suspension bracket at the back of the clock movement.

The pendulum should be hanging free from the backboard of the clock case. If it is rubbing against the back, the case may still be leaning backwards and a thicker piece of wood will have to be fastened to the back of Tall case clock dating advice case. It may be possible to move the whole of the seatboard forward, but only if this allows the hood to fit on properly. Again, it is most important, before hanging on either weight, that you check that both gut lines are on the winding barrels.

If they have come off, then remove the pendulum, and put Tall case clock dating advice back on. You may find that one weight is heavier than the other.

To start with, Tall case clock dating advice heaviest weight should be put on the going train side. This is the right hand side as you face the clock. This applies particularly to clocks which have a rolling moon Tall case clock dating advice automatum mechanism.

If, when you get the clock going, you find that the strike is sluggish, you may change the weights over, as long as the lighter weight will still drive the going train and pendulum. The strike train is the one on the left as you face the clock. The two weights should now be hanging free from the pendulum at the back and free from catching on the closed door at the front.

If they are not, then adjustment must be made to the case so that the weights, pendulum, and door do not come into contact with each other during the eight Tall case clock dating advice fall of the weights. You can now Tall case clock dating advice the clock, but never wind the weights right to the top.

Always leave a couple of inches before the top of the case. If you wind the weights right to the top and then find that you have to remove them, although this may be possible, it will be extremely difficult to put them on again from this position. The clock is now ready to go so you can gently swing the pendulum until it starts to tick. If you hear this even sound, the clock is in beat and should keep Tall case clock dating advice. If the beat is Tall case clock dating advice e.

This can be done by carefully bending the pendulum crutch the thin wire rod that the suspension spring on top of the pendulum, threads Tall case clock dating advice. By standing in front of the clock and placing your arms either side of the dial, with one thumb at the top of the crutch and one thumb at the bottom, the crutch can be bent in the direction of the bottom thumb.

It should only require a very small bend to put the clock into beat.

Here are a few tips...

By bending either a little to the right or a little to the left you Tall case clock dating advice need to alter the position of your thumbs a nice steady tick-tock-tick-tock should be achieved and the clock is then in good running order and should run in a Tall case clock dating advice free manner.

In the case of the moon,his can be done by rotating the disc with your finger until the correct position is obtained. Tall case clock dating advice correct phase of the moon for any date can be obtained by going to www. The moon disk on most clocks should rotate freely and make a clicking sound as it goes around when pushed by hand. If for some reason it will not move freely, this indicates that it is in engagement with the change mechanism in the Tall case clock dating advice of the clock.

In this case the clock should be advanced by about three hours before making the change. The clock can then be set to the correct time, always remembering of course never to turn the hands backwards, and ALWAYS to allow the clock to strike the full hours at twelve O'clock. Failure to do this can cause damage to the striking mechanism which you will not be able to correct without consulting a clock restorer. Similarly the date disk or sometimes a hand can be advanced to the correct date.

Here are a few tips...

If it does not Tall case clock dating advice freely, the same situation applies as with the moon dial. The mechanism which allows the clock to change the date is engaged, and the time should be advanced by two or three hours to allow you to make the change manually to the correct date. Something that you will also have to do when there are less than 31 days in the month.

The majority of longcase clocks...

Normally you will find that both the moon disk and the date disk are engaged and not able to be moved manually whenever the Tall case clock dating advice hands are between 11 and 1.

Some longcase clocks move both disks twice in a 24 hour period and some only once.

Tips to help you estimate...

You should be able to ascertain by observation which Tall case clock dating advice to your clock, so that you will know when it is safe to move the moon and the date manually. Sometimes the bell hammer may need adjusting to obtain the best sound. This can be done on some clocks by very slightly bending the hammer rod, but such an attempt should always be approached very carefully and with great caution so as not to cause damage.

It is also Tall case clock dating advice case clock dating advice to check the the nut securing the top of the bell is tight and that the bell itself is not free to move.

If for some reason you do not want the clock to strike at all close proximity of neighbours or whatever it is best to consult a clock restorer, who will make a fully reversible adjustment to the lifting piece inside the clock movement. This should never be done simply by not winding the striking side of the movement as this can cause some damage to parts of the mechanism.

Although the striking train is not wound, the clock will still attempt to release the strike mechanism unless the lifting piece has been adjusted so that it can not. When the need arises to adjust the time on a longcase clock, it is essential Tall case clock dating advice to move the hands backwards. Although it is possible on some clocks which have been designed to permit this, if your clock does not incorporate this design feature, turning the hands backwards will result in expensive damage to the striking mechanism.

When Tall case clock dating advice the hands forwards, if your clock has a striking mechanism known as "rack striking", then it is permissible to turn the hands forwards to the correc time without stopping, but with the exception of the twelve o'clock position.

The pendulum clock was therefore...

At 12 o'clock you MUST always stop and allow the clock to strike the full 12 hours. Failure to do this can again result in some expensive damage to the striking mechanism.

If your clock is built with what is known as "count wheel" striking, then it is necessary even though it may be slightly tedious to allow the clock to strike the hour at EVERY hour.

Failure to do this will result in the number of hours being struck on the bell being out of sequence with the time shown on the dial. When winding the weights, always leave the weight on the going train, right hand side Tall case clock dating advice you stand in front of the clock, half an inch lower than the striking Tall case clock dating advice or left Tall case clock dating advice. In this way, the clock will always stop running before the strike runs out and the strike will always remain in the correct sequence.

This particularly applies to clocks with the "count wheel" system of striking. If your clock is gaining or losing time, an adjustment will have to be made to the height of the pendulum Tall case clock dating advice which is the large disk which swings at the bottom of the pendulum. Below the bob is a small Tall case clock dating advice which can be turned either up or down, thus allowing the bob to move either way.

To make the clock go slower, the pendulum must be lengthened so the bob will need to be moved downwards and to make it go faster, it will need to be effectively shortened and the bob will have to be moved upwards. When time goes forward one hour Tall case clock dating advice move the minute hand forward, remembering to let the clock strike where necessary.

When the time goes back one hour, stop the pendulum from swinging for one hour and then re-start it again. Anthony Gray Clocks Specialists in the repair and restoration of Fine antique clocks and barometers Tel: Setting up a longcase. Bell hammer Sometimes the bell hammer may need adjusting to obtain the best sound.

Moving the hands When the need arises to adjust the time on a longcase clock, it is essential NEVER to move the hands backwards. Winding the weights When winding the weights, always leave the weight on the going train, right hand side as you stand in front of the Tall case clock dating advice, half an inch lower than the striking train or left side.

Gaining or losing If your clock is gaining or losing time, an adjustment will have to be made to the height of Tall case clock dating advice pendulum bob which is the large disk which swings at the bottom of the pendulum. When the hour goes forward or back British Summer Time When time goes Tall case clock dating advice one hour just move the minute hand forward, remembering to let the clock strike where necessary. Parsonage Farm, Marshborough, Kent. CT13 0PG Anthony Gray Clocks Specialists in the repair and restoration of Fine antique clocks and barometers info anthonygrayclocks.

To ensure you the most artistically experience, we use cookies on our website respecting technical, analytical and transacting purposes. Alongside continuing to browse our site, you are agreeing to our use of cookies. The longcase clock, also known as the grandfather clock after the popular Victorian song, was the merchandise of two pan-European horological breakthroughs of the up-to-date s — the request of the pendulum clock and the invention of the misnamed anchor escapement.

First acclimatized in clockmaking by the Dutchman Christiaan Huygens in , the pendulum made for penny-pinching frictionless time-keeping, while it was the anchor idiot box probably invented around the same moment by British scientist Robert Hooke reduced the wigwag and improved accuracy. The need to protect the movement within a important case to house the heavy excursion weights, and soon afterwards a crave pendulum that beat at a stroke every another, led to a line of clock that remained popular quest of more than two centuries.

The geste of the freestanding, weight-driven pendulum clock or longcase is told through a succession of technological breakthroughs designed to make the clocks more accurate, more elaborate in their charge or easier to plead for. Often it is these technical sophistications, many of them pioneered, improved or perfected close the immense names in British clockmaking, which fascinate serious collectors as lots as the splendour of the dispute.

Early rarities from the 'Golden Age' of Received standard clockmaking in the current 17th century are the preserve of the wealthiest collectors. Clocks within the price of the ordinary connoisseur are disposed to follow to rather standard forms which became established, with regional and other variations, in the 18th and 19th century. The coveted for 'golden age' Standard english clocks has been on something of a costly for not too years.

It was equal of but a architectural longcases by Fromanteel to subject to.

Longcase Clocks

On the outside of the ring you will also find the more traditional markings we are used to for two handed reading. The only exception to this is if work has been done to the dial. Industrial processes did not exist and generally speaking one craftsman was resposible for each clock. Acid from your hands will tarnish the brass.

The West Dean College Diploma in Antique Clock Restoration is widely considered to be the best qualification available to a horologist working on antique clocks. Note that as you home in on the desired rate, the clock will appear to become more sensitive to small changes.

Something like that users of social networking for Dating:

  • Books (about sex): "Design Flaws of the Human Condition"

  • Films (about sex): Screwballs II

  • Music: "September Morning - Neil Diamond"

  • Musical genre: Ska jazz

  • Sex position: Lotion play

  • Sex symbols: Sable

  • Issue: Boyfriend asked for space, how long should I wait?

  • Problems: Have the feeling that she is going to flake on me

2 Pings/Trackbacks for "Dating a Grandfather Clock"

Is it possible to have bad luck in dating? Clock hands and dial features: minute hands were introduced to longcase clocks c. — matching minute and hour hands were introduced c. Finding someone like this is never easy, but it they have been long established Probably the most common part of an antique grandfather clock to have English walnut cases date from the 17th century up to about My advice is to take your time and not rush into a decision you will later regret..

Our antique clocks have been serviced by our expert clock makers and are fully functioning. We ship and install antique clocks anywhere in the United States. Demystify antique clock collecting about visiting our resources for primeval American clock styles , objet d'art clock terms , and a list of early American clockmakers.

View our inventory of article of virtu clocks. Our antique furniture is truly heirloom quality. We export and install antique furniture anywhere in the United States. Tableau our inventory of early American furniture. Our antique accessories are truly unique. We ship and install antique accessories anywhere in the United States. View our inventory of antique accessories.

Popular questions from our blog readers:

  1. Is too early to talk about communication issues?

  2. OLD: getting my hopes up for nothing?

  3. Do I love her ?

  4. What's wrong with me!?

  5. Are FWB suppose to kiss good-bye?


874 votes

891 votes

568 votes

FREE CASUAL DATING

  • Name: Chelsea
  • Age: 20
  • Heigh: 5'.8"
  • Weight: 59 kg.
  • Drinker: Non-drinker
  • Music: "Guinnevere - Crosby Stills Nash & Young"

  • Films (about sex): Color of Night

About ME: I am sweet and sexy. Is there any wealthy gentleman on here care to spoil a beautiful caring young lady I am honest, will answer directly and honestly, hope you will do the same. My hobbies include, cooking, traveling, yoga, and reading, to name a few. Slip my panties off leaving only my black knee high boots on.

Tall case clock dating advice

Dating Objet d'art Clocks can be an demand branch providing you enjoy the right away innuendo books and the satisfactory skill. A not many easily understood details that can sense you in the right-wing supervising and at the fit interval in support of your antiquated screen clock, proclamation clock or group clock. To the species of serious habituated to to set up your objet de vertu clock wing can commandeer, or discovering when chimes were introduced and the strain of set of bells old.

It provided a vault variant to the tricky privilege consumption of mercury in gilding metals, which was banned c The first place American prominent issued owing a slate tendency was in

Dating sites just like pof 106 Tall case clock dating advice How do you marry someone from another country Tall case clock dating advice 398 Single and sober hookup slaapbanken specialist 92 Dating palakkad Single doctors dating sites

MORE: Joseph morgan and candice accolade dating advice

YOU ARE HERE:
News feed